A solar plant falls short of its expected output just before a scheduled delivery. Another plant in the same portfolio is producing as forecast, and a battery has energy available. The operator needs to know whether the battery can cover the shortfall, how much it can deliver in the affected interval, and what that dispatch would mean for the next commitment. A virtual power plant gives the operator a way to answer those questions across the portfolio.
What is a virtual power plant?
A virtual power plant, or VPP, uses software to coordinate multiple energy assets as a portfolio. The assets can include solar plants, wind generation, batteries and flexible loads. They remain at their own sites and operate within their individual limits. The software brings their measurements, forecasts and available flexibility together so an operator can plan and coordinate their combined output.
For an aggregator, the operational question is how much power the portfolio can deliver at a given time, for how long and under which constraints. An asset owner may use the same approach to coordinate several sites with a trading team. The commercial role of the portfolio depends on the contracts, metering arrangements and market access that apply to its assets.
How does a VPP coordinate solar plants and batteries?
Build a current view of each asset
The operator needs recent measurements from each site. For a solar plant, those can include measured output, inverter availability and the active export limit. For a battery, state of charge, available charge and discharge power, and operating alarms help determine what it can do in the next interval. The portfolio view also needs to show whether a measurement is current. A battery with stale telemetry should not be treated as fully available based on its last reported state alone.
Sites may report data through different meters, controllers or SCADA systems. Aligning measurements to a common timeline makes it possible to compare them with forecasts and scheduled deliveries. Site-level visibility still matters. A portfolio total can hide the fact that one connection is already at its export limit while another has room available.

/
Forecast generation and plan flexibility
Solar and wind forecasts estimate generation over the delivery intervals that matter to the portfolio. The planning team compares those estimates with its commitments and considers how a battery or flexible load could respond if conditions change. A battery scheduled to discharge later in the day may have limited energy available for an earlier correction. Using it now can change the plan for later intervals.
Forecast updates also help the operator distinguish a likely shortfall from a brief deviation. A cloud front moving across several solar plants can have a different effect from an inverter outage at one site. The guide to solar power forecasting and imbalance costs explains how these revisions can affect a trading position.
Dispatch available assets and verify delivery
Once the operator selects a response, the control layer can pass a setpoint to an eligible asset where integration and operating permissions allow. The next step is to verify the response against metered output. If the battery delivers less than expected or a connection limit changes, the operator needs to see the residual exposure and decide whether another action is feasible.
A worked example of a solar shortfall
Assume an aggregator has scheduled 10 MWh of delivery in a 30-minute interval. The latest forecast lowers expected generation across two solar plants from 10 MWh to 8.5 MWh. The expected shortfall is 1.5 MWh. The numbers are illustrative and refer to the same delivery interval.
The portfolio has a battery with 2 MWh of usable discharge energy and a 2 MW discharge limit. Even with enough energy in storage, the battery can deliver at most 1 MWh in 30 minutes at 2 MW. Suppose the battery site has only 1.6 MW of export headroom because local solar generation is using part of the connection. Over that interval, the feasible battery contribution falls to 0.8 MWh, assuming the available headroom stays constant.
The portfolio would then still expect a 0.7 MWh gap. If an intraday adjustment is available, the trader can assess whether to cover the remaining volume. The operator also checks the battery’s later commitments before committing the 0.8 MWh. After delivery, metered generation and the final trading position determine how much deviation remains under the applicable settlement arrangement.
This example separates stored energy from deliverable energy. The decision depends on battery power, connection capacity and timing as well as charge level. The companion article on when to charge and discharge a solar battery works through the cost side of a dispatch decision.
What makes a renewable portfolio ready for a VPP?
Start with an inventory of the assets and what can be measured or controlled at each site. Record the meter boundary, available telemetry, export limit, and the operating constraints that an automated dispatch must respect. Some assets may be suitable for monitoring and forecasting before they are ready for remote control. Giving each site an explicit role helps the operator distinguish expected generation from flexibility that can be called on.
Next, agree how the operations and trading teams will work together. They should know who can approve a dispatch, how the team responds if communications fail, and how changes to delivery schedules are recorded. When an operator overrides an automated plan, recording the reason helps the team distinguish a forecast error from a deliberate change in strategy.
Finally, evaluate performance over actual delivery intervals. Compare planned and metered output, check how quickly assets respond, and review where the portfolio encountered battery or connection limits. That record helps identify whether a missed delivery came from a forecast revision, unavailable equipment or an assumption about flexibility that the site could not meet.
Where does market access fit in?
A portfolio can use VPP software to coordinate its assets even when the available trading or flexibility products vary by market. A team operating across Serbia, Croatia, Bosnia and Herzegovina, Montenegro or North Macedonia should map each asset to its own contractual and metering arrangements before assuming it can contribute to a particular commercial commitment. Define how the resulting position will be measured and reconciled alongside the physical dispatch plan.
For a portfolio manager, it helps to review physical and commercial availability separately. A battery can be technically capable of discharging and still be committed elsewhere. A trader can see an attractive price and still face a site export limit. The combined view tells the team which actions it can actually take.
Managing solar and battery assets with Benjo Energy
The Benjo Energy Management Platform combines portfolio monitoring, production and price forecasts, and asset control in one environment. For teams operating several renewable sites, that provides a shared view of expected generation and available battery flexibility. To discuss how a VPP workflow could fit your portfolio, contact Benjo Energy.

